|[Lighting Accessories] - [Lighting Fixtures] - [Switch]|
SD Card Programming Symphony LED light bar controller | point control 2048 pixels T-1000B Controller
Hello friends Shenzhen Shang Mingguang Power Co., Ltd. welcome your visit Thank you for your concern about our company and products;!!! Some of us do not give you good service apologize for the inconvenience, please for your understanding if we have what you need, please tell us your needs, so that we can serve you better and faster; If our products can not meet your needs or you to our products and services are not satisfied, please criticism, correction so that we can timely corrections and continue forward!
T-1000B Owner's Manual
A, T-1000B System Features
1,32 level -65536 level grayscale control, software Gamma correction.
2, support a variety of point, line, surface light source, supports a variety of rules, shaped handle.
3, single-port controller output, with a maximum of 2048 pixels.
4, line control, play content stored in the SD card.
5, T-1000B store up to 16 files, multiple files sequentially copied to the SD card.
6, stored in the SD card effect should then be named: 00_1.led, 01_1.led, 02_1.led.
7, when the IC is compatible with single-lane, single-wire connection IC lamps, no need CLK clock line.
NOTE: When 1 T-1000B ports with load 512 lights, the playback speed of up to 30 frames / sec ports with load more than 512 lights, with a frame rate
Increase the number of lights automatically reduced.
Second, support chips:
Third, the appearance of the picture:
Fourth, the silk screen meanings:
TTL signal (signal 245):
Note: TTL output signal for the controller must be carried out for the land and fixtures (that is, the ground and the output ground lighting controller connected together).
Note: 1, T-1000B is a single output port, with up to 2048 pixels;
2, when the control IC single line simply controllers DAT and DAT and GND and lamps connected to GND corresponds When the control needed to double IC and GND with controller DAT.CLK lamps DAT, CLK and GND should be connected to the relative.
3, the new editor in effect when the software project, the selection control model: T-1000B-IC models
Six file storage:
File naming rules:
The effect of naming a single controller
'00_1.led' - 1st effect
'01_1.led' - the first two effects
'02_1.led' - 3rd effect
'03_1.led' - 4th effect
Seven specific parameters:
Type: SD Card
Format: FAT format
Store files:. * Led
Working temperature: -30 ℃ -85 ℃
Power supply: DC 5V input
Power consumption: 1W
Data transfer port: 3pin Terminal
Weight: 0.25Kg with packaging (3pin Terminal * 1; SD card * 1; Power Adapter * 1; Tray * 1)
Before you copy files to the SD card, you must format the SD card, note must be formatted before each copy.
SD card must be formatted as 'FAT' format.
Note: SD card not hot-swappable controllers, that is, each time plug SD card, you must disconnect the power controller.
Eight, to common problems:
Question 1: After power, found T-1000B error ERROR indicator has been flashing, and no effect output
A: The error LED blinks ERROR been proved correct reader controller is not, possible problems are:
①SD card inside is empty, there is no effect file.
②SD card inside the effect file * .led files and controller model does not match the latest version LedEdit 2012 inside the correct choice of the model T-1000B- controller chip model, and re-create the effect of file * .led.
③SD card before copies are not formatted as FAT file kinds.
④ Check the supply voltage of the controller, the controller can be used alone to supply power to exclude reason.
⑤ Replace the SD card before testing, SD card bad exclude the possibility.
⑥ effect file name is wrong, change 00.led.
Question 2: When the controller is powered, normal light, but no effect lighting changes
A: The reasons for this are the following:
① Check the lighting signal line and the controller is not connected properly.
② lamps and controllers must be common ground that the lamp to ground and ground controllers tied together.
③ Please check in SD Card * When .led effect file if the selected model is consistent with the current luminaires chip.
Question 3: When connected to the controller and the lamps, strobe lamps, and have the effect of changes while the controller LEDs show normal.
A: ① ground between the controller and the fixtures are not connected.
Effect did ②SD card inside is wrong, do not match the selected effect when the actual lighting fixtures chips and chips.
③ supply voltage insufficient lighting.
Question 4: SD card can not be formatted.
A: ① first confirm whether the side of SD card protection switch has been unlocked unlocking direction SD card lilies this end.
② protect the lock has been designed according to the requirements, but still can not be formatted, if this is the case the majority of SD card reader is broken, replace the SD card reading device.
③ If the above actions do not solve formatting problems, replace the SD card, re-test.