|[Lighting Accessories] - [Lighting Fixtures] - [Switch]|
Music Symphony controller | controller voice Symphony | SD programming voice Symphony full-color controller
Symphony music controller 803sc voice instructions
Symphony Music Sound LED Controller 803sc is music controller can automatically play various effects according to the strength and rhythm of the music. Four kinds of play mode, you can control single, double, three-wire, four-line LED driver chips, two outputs ports, controls up to 3072 points. If there is no SD card music profile (* .hmc), controls up to 4096 points.
Supporting software (LED preparation software) V3.87 and above.
Second, the controllable driver chip
Current driver chip can be controlled have LPD6803, LPD8806, LPD6813, LPD1882, LPD1889, LPD6812, LPD1886, LPD1883; UCS6909, UCS6912, UCS1903, UCS1909, UCS1912; WS2801, WS2803, WS2811, WS2812; TM1812, TM1809, TM1804, TM1803, TM1829 , TM1926, TM1914; LX1003, LX2003, LX2006, DMX512, HDMX, APA102, P9813, DZ2809, INK1003, BS0825, BS0901, TLS3001, TLS3002, SD600, SM16711, SM16716, SM16726, LD1510, LD1512, LD1530, LD1532, MBI6023, MBI6024 Wait.
Three-wire control, use only a four-port LED driver chips, such as DM114, DM115, DM13C, DM134, DM135, DM136; MBI5001, MBI5168, MBI5016, MBI5026, MBI5027, TB62726, TB62706, ST2221A, ST2221C, 74HC595,6B595, XLT5026, ZQL9712, ZQL9712HV, HEF4094, A8012 and the like.
NOTE: LD151x only support 16-bit and 8-bit mode, SM16726 only supports SET = 1.
Third, the performance characteristics
1, two output ports, control a total of 3072 points, if no SD card music profile can control 4096 points.
2, can automatically play various effects according to the strength and rhythm of the music, but also can play DAT files.
3 the four play modes, and support power synchronous differential signal synchronization.
4, microphone and headphone audio support base.
5, SD card support FAT32, FAT16 format, the maximum capacity of 64G bytes, allowing up to 64 DAT files.
6, LED driver IC type, etc. on the scan clock (LED preparation software) software settings.
Third, the use
1, SD card for the first time, or delete multiple needs to be formatted as FAT16 or FAT32 format allows storage of up to 64 DAT file, the controller displays the alphabetical sorting by file name.
2, the controller is powered, digital display 3C, if there is no SD card inserted, the left LED is blinking '3', if the right side of the LED is blinking indicates SD card or deck problems, flashing numbers indicate corresponding error. the right of the digital display 'A' indicates that the AC power supply can be AC synchronous; display 'b' said that as the playback speed is set too fast to power synchronization; show 'd' denotes a DC power supply, no AC synchronous function; display 'H' represents the difference synchronization signal transmitter display 'F0' means no DAT file. If the controller type error display 'FE', points or too much display port 'Fb'.
3, two buttons for the 'MODE' and 'SPEED', press the 'SPEED' button, if the current mode is displayed in the status display is switched to speed, if the currently displayed speed is adjusted playback speed. Press the 'MODE' button, If the current display is the speed switch to the status display mode if the current mode is displayed in the state, short press to change the mode, press and replace the state.
4, the pattern represented by the 0-7, 0: DAT sequentially, 1: DAT Speed, 2: DAT music, 3-7: Automatic music, only one has nothing to do with the sound.
5, including the status of 'A', 'd' and 'H', 'H' represents the differential synchronization signal transmission, 'A' denotes an AC power supply, 'd' denotes a DC power supply. When using differential synchronization, only one control It is set to 'H'.
6, when (LED preparation software) set the style, be sure to select the type of controller SC.
Do DAT file, you can select a sub-control two lines, each line may not be more than 1536 points; a line can also choose a sub-control, this route can not be more than 3072 points.
Making music profile (* .HMC), the width and height must not exceed 128 points wide by height no greater than 3072, when wiring lights to not overlap, points should not exceed 3072 points.
If the SD card is also available in HMC file with the DAT file, they correspond to the requirements of the same shape, LED driver chip type to be consistent.
If the hold music profile SD card (* .hmc), a sub-control to select two lines, each line up to 2048 points; a sub-control to select a line, this line can reach 4096 points the controller. control points indicate only the ability to send the controller, the actual control points associated with specific lamps.
7, Music profile (* .hmc), contains light shapes (eg lamps connections), LED driver chip type, lamp type, scan clock, color is negated and color plate production method is as follows:
In (LED preparation software) color panel, you need to select the current color, hats beat note when using these colors, but also set the palette, a variety of sound effects require the use of a maximum take 128 colors, the less will be recycled .
Set shape, and light settings, and then click the window in the shape of the light 'File' - 'Symphony Music Voice output controller 803sc profile'.
8 Music mode requires only hmc file, no DAT file; the other three models only DAT files, when these two files simultaneously into SD card.
Fourth, buttons and display
1. Press the speed key to cycle set the playback speed, and with a digital display tube.
2. Press the Mode button to set the loop playback mode, and display digital tube left.
3, long press the mode key, set the synchronization status, and the right of the digital display. When using differential synchronization, only one controller is set to 'H'.
Fifth, the controller interface definitions
Seven, wiring methods
A signal line connected to the controller's D +
Shang Mingguang electric -shinmi Description:
(2), 3528,5050 series RGB, Happy Valley, running water, scanning, full-color, Symphony LED flexible light strip
(3), 3528,5050 series 220v high voltage LED lights;
(5), LED lights power supply
Shang Mingguang electric -shinmi Company:
Shenzhen Shang Mingguang Power Co., Ltd. (www.ledrdt.com 0755-33291948 15818578585 QQ: 2602165622) is a collection development, production and sales of LED light bar, LED soft light, light bar, with lights, LED lights, LED lights and supporting the power supply, controller and other products of professional high-tech companies. companies adhering to the "customer first, forge ahead 'business philosophy, adhere to the' customer first 'principle to provide our customers with quality service. Welcome!
Shang Mingguang electric -shinmi Contact:
Mobile phone: 15818578585
Address: China's Shenzhen City, Guangdong Shenzhen Ocean Pearl Greeting pit Jianye Road