[Desktops & Servers] - [Industrial Computer & Accessories] - [Industrial Computer & Accessories]

Unlocked Linksys SPA3000 SPA-3000 SIP VOIP Gateway

Unlocked Linksys SPA3000 SPA-3000 SIP VOIP Gateway
  • Unlocked Linksys SPA3000 SPA-3000 SIP VOIP Gateway
Product code: 26331000001
Unit price: 23.05 USD
Price unit: Per piece
Minimum order:
Other info:
Visit my shop

The SPA-3000 features VoIP adapter functionality found in the SPA-2000 and SPA-1000/1 with the additional benefit of an integral connection for legacy telephone network hop-on, hop-off applications. SPA-3000 users will be able to leverage their broadband phone service connections more than ever by automatically routing local calls from cell phones and land lines to a VoIP service provider and vice versa.

A typical user calling from a land line or mobile phone will be able to reduce and even eliminate international and long distance telephone charges by first calling their SPA-3000 via a local phone number or by using a telephone connected directly to the unit. The advanced authentication and call routing intelligence programmed into the SPA-3000 will connect the caller via the Internet to the far end destination with security and ease. Using the SPA-3000 at the far end, calls can be answered immediately or further processed as a local call to any legacy land line or mobile phone allowed by the SPA-3000 dial plan.

If power and/ or IP network connectivity is lost to the unit or the VoIP service is down, calls can be sent to a traditional carrier via the FXO interface.

We have seen instances where installing the SPA3000 behind a firewall which blocks ICMP packets causes problems with registration. Try turning off any ICMP blocking on your firewall.


1: VoIP to PSTN (USA) Service Call Origination and Termination
2: PSTN (USA) to VoIP Service Call Origination and Termination
3: Single or Dual Stage Dialing
4: Service Authentication via PIN, Digest, Caller ID (Bellcore Type 1)
5: Per Call Authentication and Associated Routing
6: Least Cost Routing Support
7: Terminating Impedance Agnostic - 8 Configurable Settings
8: Call Waiting, Cancel Call Waiting
9: Caller ID Detection (Bellcore Type 1)
10: Caller ID with Name/ Number (Multinational Variants) Display
11: Caller ID Blocking
12: Call Waiting Caller ID with Name/ Number
13: Call Forwarding to PSTN or VoIP Service: No Answer/ Busy/ All
14: Do Not Disturb
15: Call Transfer
16: Three-Way Conference Calling with Local Mixing
17: Message Waiting Indication - Visual and Tone Based
18: Call Return and Call Back on Busy
19: Call Blocking with Toll Restriction
20: Distinctive Ringing
21: Off-Hook Warning Tone
22: Selective/ Anonymous Call Rejection
23: Hot Line and Warm Line Calling
24: Speed Dialing of 8 Numbers/ Addresses
25: Music on Hold
26: Forward Calls to VoIP service - Selective, Authenticated, All
27: Forward Calls to PSTN service - Selective, Authenticated, All
28: PSTN Line Sharing with Multiple Extensions
29: Automatic PSTN Fallback (Loss of Power or IP Service to Unit - with Quiescence to Normal Operations)
30: Advanced Inbound and Outbound Call Routing
31: Single Stage and Two Stage Dialing
32: Independent Configurable Dial Plans - Up to 8
33: Force PSTN Disconnection
34: Sequential Dialing Support
35: Dimensions: (L*W*H) 102*95*27mm
36: Unit Net Weight: 119g

VoIP to PSTN Authentication and Routing

1: VoIP to PSTN Gateway Enable/ Disable
2: VoIP Caller Auth Method (None, PIN, HTTP Digest)
3: VoIP PIN Max Retry Setting
4: One Stage Dialing Enable/ Disable
5: VoIP Caller ID Pattern Matching
6: VoIP Access Allowed Caller List (No Further Authentication)
7: VoIP Caller PIN and Associated Dial Plan

PSTN to VoIP Authentication and Features

1: PSTN to VoIP Gateway Enable/ Disable
2: Caller Auth Method: None, PIN, Caller ID
3: Ring Through to FXS Enable/ Disable
4: Ring Through Tone - Configurable
5: Caller ID (Bellcore 1) for VoIP Service Access
6: Caller ID Enable/ Disable
7: PIN Max Retry Settings
8: Access Allowed Caller List (No Further Authentication)
9: Caller PIN and Associated Dial Plan
10: Least Cost Routing (via Outbound VoIP - Line1 Dial Plan)

FXO Behavior

1: VoIP Answer Delay Timer
2: PSTN Answer Delay Timer
3: VoIP PIN Digit Time-Out Timer
4: PSTN PIN Digit Time-Out Timer
5: PSTN-to-VoIP Call Max Dur Timer
6: VoIP-to PSTN Call Max Dur Timer
7: PSTN Ring Through Delay Timer
8: PSTN Dialing Delay Timer
9: VoIP DIG Refresh Interval Timer
10: PSTN Ring Time-out Timer

PSTN Disconnection Detection

1: CPC (Removal of Tip/ Ring Voltage Momentarily)
2: Polarity Reversal
3: Long Silence (Confugrable Time Setting)
4: Disconnect Tone (e.g. Reorder Tone)
5: FXO Port Impedance - Configurable to 16 settings
6: Ring Frequency - Configurable
7: SPA to PSTN and PSTN to SPA Gain Settings
8: Ring Frequency - Maximum Setting
9: Ring Validation Time Setting
10: Tip/ Ring Voltage Adjustment Setting
11: Ring Indication Delay Setting
12: Operational Loop Current Minimum Value
13: Ring Time-out Setting
14: On-Hook Speed Setting
15: Ringer Impedance Setting
16: Line-in-Use Voltage Setting

Regulatory Compliance

FCC (Part 15 Class B and Part 68) , CE, ICES-003

1: Password Protected System Reset to Factory Default
2: Password Protected Admin and User Access Authority
3: Provisioning/ Configuration/ Authentication:
4: HTTP Digest - Encrypted Authentication via MD5 (RFC 1321)
5: Up to 256-bit AES Encryption

1: Quick-Start Installation and Configuration Guide
2: User Guide
3: Administration Guide - Service Providers Only
4: Provisioning Guide - Service Providers Only

Data Networking
1: MAC Address (IEEE 802.3)
2: IPv4 - Internet Protocol v4 (RFC 791) upgradeable to v6 (RFC 1883)
3: ARP - Address Resolution Protocol
4: DNS - A Record (RFC 1706) , SRV Record (RFC 2782)
5: DHCP Client - Dynamic Host Configuration Protocol (RFC 2131)
6: ICMP - Internet Control Message Protocol (RFC792)
7: TCP - Transmission Control Protocol (RFC793)
8: UDP - User Datagram Protocol (RFC768)
9: RTP - Real Time Protocol (RFC 1889) (RFC 1890)
10: RTCP - Real Time Control Protocol (RFC 1889)
11: DiffServ (RFC 2475) , Type of Service - TOS (RFC 791/1349)
12: SNTP - Simple Network Time Protocol (RFC 2030)

Voice Gateway
1: SIPv2: Session Initiation Protocol v2 (RFC 3261, 3262, 3263, 3264)
2: SIP Proxy Redundancy - Dynamic via DNS SRV, A Records
3: Re-registration with Primary SIP Proxy Server
4: SIP Support in Network Address Translation Networks - NAT (incl. STUN)
5: Secure (Encrypted) Calling via Pre-Standard Implementation of Secure RTP
6: Codec Name Assignment

Fax Capability
1: Fax Tone Detection and Pass-Through (Using . 711)
2: DTMF: In-band & Out-of-band (RFC 2833) (SIP Info)
3: Flexible Dial Plan Support with Interdigit Timers and IP Dialing
4: Call Progress Tone Generation
5: Jitter Buffer - Adaptive
6: Frame Loss Concealment
7: Full Duplex Audio
8: Echo Cancellation (G. 165/ G. 168)
9: VAD - Voice Activity Detection with Silence Suppression
10: Attenuation / Gain Adjustments
11: Flash Hook Timer
12: MWI - Message Waiting Indicator Tones
13: VMWI - Visual Message Waiting Indicator via FSK
14: Polarity Control
15: Hook Flash Event Signaling
16: Caller ID Generation (Name & Number) - Bellcore, DTMF, ETSI
17: Music on Hold Client
18: Streaming Audio Server - up to 10 sessions

Provisioning, Administration & Maintenance:
1: Web Browser Administration & Configuration via Integrated Web Server
2: Telephone Key Pad Configuration with Interactive Voice Prompts
3: Automated Provisioning & Upgrade via HTTPS, HTTP, TFTP
4: Asynchronous Notification of Upgrade Availability via SIP NOTIFY
5: Non-intrusive, In-Service Upgrades
6: Report Generation & Event Logging
7: Stats in BYE Message
8: Syslog & Debug Server Records - Per Line Configurable

Physical Interfaces:
1: 1 10baseT RJ-45 Ethernet Port (IEEE 802.3)
2: 1 RJ-11 FXS Phone Ports - For Analog Circuit Telephone Device (Tip/ Ring)
3: 1 RJ-11 FXO Phone Ports - For a Telco or PBX Connection

FXS: Subscriber Line Interface Circuit (SLIC) :
1: Ring Voltage: 40-55 VRMS Configurable l*
2: Ring Frequency: 10 Hz - 40 Hz l*
3: Ring Waveform: Trapezoidal and Sinusoida l*
4: Maximum Ringer Load: 3 REN
5: On-hook/ off-hook Characteristics:
6: On-hook voltage (tip/ ring) : -50 V NOMINAL
7: Off-hook current: 25 mA min
8: Terminating Impedance: 8 Configurable Settings including
9: North America 600 ohms, European CTR21

Power Supply:
1: DC Input Voltage: +5 VDC at 2.0 A Max.
2: Power Consumption: 5 W

Indicator Lights/ LED:

LAN Activity/ Link LED, Status LED (In-Use, Povisioning, Idle, Alert)

The SPA-2100 supports up to 2 sessions using G. 729. The SPA-1001, SPA-2002 and SPA-3000 support one G. 729 session

Package Includes:

  • 1 x SPA3000 Phone Adapter
  • 1 x Power Adapter
  • 1 x RJ45 Ethernet Cable
  • 1 x stander