Ricoeur instrument supply stainless steel bulk density meter, the powder bulk density meter, bulk density meter, bulk density tester

Ricoeur instrument supply stainless steel bulk density meter, the powder bulk density meter, bulk density meter, bulk density tester
 

Product description:

Brand: Ricoeur Instrument Model: 101
Detailed description:
Custom processing: Measuring range: bulk density meter stainless steel, powder bulk density meter, bulk density meter, bulk density determination
Type: Desktop density meter Division value: 1
Accuracy: 1 Purpose: stainless steel bulk density meter, the powder bulk density meter, bulk density meter, bulk density determination
Variety: vibrating Power: 1 (V / HZ)
Display: 1 Custom processing:
Measuring range: Types of:
Dividing the value of: Accuracy:
use: Variety:
power supply: display method:

FT-106A powder bulk density tester

FT-106A powder bulk density tester standard requirements :

It is based on the international standard ISO9136-2: (E) (abrasives - Determination of bulk density - Part II: Powder) 1999 related to the technical requirements of development and production of special detection equipment.

FT

FT-106A powder bulk density tester works The powder tested loading hopper, a bulk powder under its own role in the steady state. When the electromagnetic oscillator startup, powder under the action of electromagnetic vibration in specific ways and means of measuring flows into the bucket, will fall to Calibrating measuring cylinder of powder, Weigh Calibrating measuring cylinder soot mass in the balance, and then divided by the measurement cylinder volume, you can measure the bulk density of the test Powder

-106A Powder bulk density tester main pieces Instrument by the splice parts, vibration feed section, electrical control components.

FT-106A powder bulk density tester Scope : Suitable for detecting manufacturing bonded abrasives and coated abrasives with powder bulk density, but also for the detection of diamond powder and bulk density of other fine powdery material, its detection methods and results and international common detection method has complete versatility.

FT-106A powder bulk density tester main technical parameters

Funnel Material: Stainless Steel;

Funnel Dimensions: Height 290mm; catchy diameter 190mm; spout inner diameter: 28mm; spout height: 38mm

Vibration slot Material: Stainless Steel

Vibration tank size: (210mm * 40mm * 30mm) ± 1mm

Measuring cylinder dimensions: diameter 64mm; inner height 62.2mm

Measuring cylinder V: (200 ± 0.5) cm3

Measurement error: ≤ ± 0.02g / cm3

Under funnel mouth diameter: 28mm; cylinder volume: 200ml; funnel spout height: 38mm; height of the drop measured powder: 140mm.

Ricoeur instrument company offers related products : FT-106A powder bulk density tester; FT-106 ordinary abrasive bulk density tester;

FT-106B superhard material bulk density tester

Measurement methods

5.1 Preparation of test specimens

5.1.1. The test sample placed in an oven at 1100 C and dried at a temperature of 1 hour, cooled to room temperature before measurement.

5.1.2. The test sample divided into thirds, removing one of which measuring bulk density, and the other two aside.

5.2 Measurement procedures

5.2.1 The best at room temperature (23 ± 2) 0 C; relative humidity is detected at (50 ± 6)% of the environment.

5.2.2. The test sample into the instrument of the funnel, the test specimen under its own stacking interactions in a stable state.

5.2.3. Press the electrical control part of the power switch, power indicator light. Then press electrical control vibration switch, then vibration indicator light, electromagnetic oscillator to work. Powder under the action of electromagnetic vibrations to specific ways and means of measuring flows into the bucket. inflow powder should be smooth, continuous process and there are rules.

5.2.4. When measuring soot deposited on the barrel of the center, and above the upper edge of the measuring bucket when 2cm ~ 3cm, electrical control vibration switch is pressed again part of the electromagnetic oscillator is stopped. Press the electrical control again power switch off the power supply.

5.2.5. The shield removed, should be careful not to remove the rest of the collision.

5.2.6. With a flat scraper will accumulate on top of the powder in the measuring bucket scrape, scraping the barrel when the angle between the blade and the measuring surface is about 450 This process should prevent the compaction of powder measuring cylinder to avoid vibrations.

5.2.7 In the division value of not more than 0.01g of weighing scales on measuring quality powder keg and barrel, minus the measurement quality of the barrel, the barrel Powder quality measurement results.

5.2.8. The measurement process, powder keg of time flowing in the survey should be controlled between 30-90 seconds. Micronized inflow time can be part of the amplitude of the electrical control by adjusting the knob to adjust, adjust the funnel to the bottom surface of the guide groove between vibration Distance may also influence the inflow velocity Powder.

5.2.9. In the whole measurement process, should always avoid vibration measurements barrel.

5.3 Data Processing

Bulk density is calculated as follows:

PB= M1/V

Where: P B - Powder bulk density, unit: g / cm3;

M1 - Quality measuring cylinder powder, unit: g;

V - the volume of the measuring cylinder, unit: cm3.

5.4. Follow the steps 5.2.1 - 5.3 Bulk density measurements other duplicate samples.













FT-106A powder bulk density tester

FT-106A powder bulk density tester standard requirements :

It is based on the international standard ISO9136-2: (E) (abrasives - Determination of bulk density - Part II: Powder) 1999 related to the technical requirements of development and production of special detection equipment.

FT

FT-106A powder bulk density tester works The powder tested loading hopper, a bulk powder under its own role in the steady state. When the electromagnetic oscillator startup, powder under the action of electromagnetic vibration in specific ways and means of measuring flows into the bucket, will fall to Calibrating measuring cylinder of powder, Weigh Calibrating measuring cylinder soot mass in the balance, and then divided by the measurement cylinder volume, you can measure the bulk density of the test Powder

-106A Powder bulk density tester main pieces Instrument by the splice parts, vibration feed section, electrical control components.

FT-106A powder bulk density tester Scope : Suitable for detecting manufacturing bonded abrasives and coated abrasives with powder bulk density, but also for the detection of diamond powder and bulk density of other fine powdery material, its detection methods and results and international common detection method has complete versatility.

FT-106A powder bulk density tester main technical parameters

Funnel Material: Stainless Steel;

Funnel Dimensions: Height 290mm; catchy diameter 190mm; spout inner diameter: 28mm; spout height: 38mm

Vibration slot Material: Stainless Steel

Vibration tank size: (210mm * 40mm * 30mm) ± 1mm

Measuring cylinder dimensions: diameter 64mm; inner height 62.2mm

Measuring cylinder V: (200 ± 0.5) cm3

Measurement error: ≤ ± 0.02g / cm3

Under funnel mouth diameter: 28mm; cylinder volume: 200ml; funnel spout height: 38mm; height of the drop measured powder: 140mm.

Ricoeur instrument company offers related products : FT-106A powder bulk density tester; FT-106 ordinary abrasive bulk density tester;

FT-106B superhard material bulk density tester

Measurement methods

5.1 Preparation of test specimens

5.1.1. The test sample placed in an oven at 1100 C and dried at a temperature of 1 hour, cooled to room temperature before measurement.

5.1.2. The test sample divided into thirds, removing one of which measuring bulk density, and the other two aside.

5.2 Measurement procedures

5.2.1 The best at room temperature (23 ± 2) 0 C; relative humidity is detected at (50 ± 6)% of the environment.

5.2.2. The test sample into the instrument of the funnel, the test specimen under its own stacking interactions in a stable state.

5.2.3. Press the electrical control part of the power switch, power indicator light. Then press electrical control vibration switch, then vibration indicator light, electromagnetic oscillator to work. Powder under the action of electromagnetic vibrations to specific ways and means of measuring flows into the bucket. inflow powder should be smooth, continuous process and there are rules.

5.2.4. When measuring soot deposited on the barrel of the center, and above the upper edge of the measuring bucket when 2cm ~ 3cm, electrical control vibration switch is pressed again part of the electromagnetic oscillator is stopped. Press the electrical control again power switch off the power supply.

5.2.5. The shield removed, should be careful not to remove the rest of the collision.

5.2.6. With a flat scraper will accumulate on top of the powder in the measuring bucket scrape, scraping the barrel when the angle between the blade and the measuring surface is about 450 This process should prevent the compaction of powder measuring cylinder to avoid vibrations.

5.2.7 In the division value of not more than 0.01g of weighing scales on measuring quality powder keg and barrel, minus the measurement quality of the barrel, the barrel Powder quality measurement results.

5.2.8. The measurement process, powder keg of time flowing in the survey should be controlled between 30-90 seconds. Micronized inflow time can be part of the amplitude of the electrical control by adjusting the knob to adjust, adjust the funnel to the bottom surface of the guide groove between vibration Distance may also influence the inflow velocity Powder.

5.2.9. In the whole measurement process, should always avoid vibration measurements barrel.

5.3 Data Processing

Bulk density is calculated as follows:

PB= M1/V

Where: P B - Powder bulk density, unit: g / cm3;

M1 - Quality measuring cylinder powder, unit: g;

V - the volume of the measuring cylinder, unit: cm3.

5.4. Follow the steps 5.2.1 - 5.3 Bulk density measurements other duplicate samples.