True Density Tester | apparent density tester | bulk density tester

True Density Tester | apparent density tester | bulk density tester
 

Product description:

Brand: Ricoeur Instrument Model: 105
  • Types of: other
Detailed description:
Whether to provide custom processing: Yes Type: Density Tester
Measuring range: freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability Samples can be measured state: can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability
Repeatability error: 1 Dimensions: 112 (mm)
Scope: can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability Specifications: can freely flow through the aperture of 2.5mm standard
Whether to provide custom processing: Yes Type: Density Tester
Measuring range: freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability Samples can be measured state: can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability
Repeatability error: 1 Dimensions: 112 (mm)
Scope: can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability Specifications: can freely flow through the aperture of 2.5mm standard



FL4-1 flowability and bulk density measuring device measuring bulk density bulk density measuring device

Where can freely flow through the aperture of 2.5mm standard funnel powder, you can use this instrument to measure powder flowability. Powder flowability to 50g metal powder to flow through a standard funnel needed to represent.

We also accompanied by 100 g GBW12004 national standard level for calibration equipment.

In addition to the aperture of 2.5mm standard funnel, we also provide a pore size of 5.0 standard funnel.

Where can freely flow through the aperture of 2.5mm, 5.0mm standard funnel powder can use this instrument to measure the metal powder bulk density.

The instrument according to GB1479-84, GB1482-84 Standard Specification for production.

FL4-1 flowability and bulk density measuring device for measuring powder flowability and bulk density, this instrument is equipped with a metal powder flowability measurement standard substance with emery GBW12004.
Under funnel diameter: φ2.5㎜ and φ5.0㎜

Angle: 60 degrees
Capacity: 25 ml ℃ Contact Zeng Sheng Phone: 15088416993

Bulk density measuring device measuring bulk density bulk density measuring device

Meet the Japanese JIS, American ASTM standards.
Sample powder: pigment / dye fine powder
specification:
Under funnel path / angle: φ15㎜ / 40
Capacity: 30 ml ℃

KURAMOCHI Bulk Density
Meet the Japanese JIS, American ASTM standards.

With the following specifications:

K-5101 (1964) K-6721 (1966) K-7365 / ISO-60 (1999) K-6911 (1962) K-6891 (1964) K-6200 / K-6223 (1972) K-3362 (1970)

K-1467 (1965) R-6126 (1970) Z-2504 (1979) Z-2502 (1966) H-1902 (1977) ASTMD-1895-A ASTMD-1895-B imported from Japan

NOTE: There is also supporting the product, please keep in touch Contact Zeng Sheng Phone: 15088416993

Density Tester | Solid Density Tester | true density analyzer | apparent density tester | absorptiometry instrument | bulk density tester | asphalt density tester | theoretical maximum density tester | Oil Products Density Tester | line density meter | hydrometer | densitometer | densimeter | densitometer | Liquid Density Meter | Digital densitometer | Rubber density meter | electronic density meter

XBM-1 / XBM-2 Apparent density analyzer

The instrument is mainly used to set aside provisions funnel Determination of apparent density of plastic bulk material, measured apparent density for PVC resin

The chemical industry as well as plastic profile factory quality inspection of raw materials into the plant ideal testing equipment. Products meet GB / T3402 , GB / T1636 And other standards.
Technical parameters: XBM-1 in line with GB / T1636, XBM-2 in line with GB / T3402
The main components: base, cage, funnel, flapper, by the feeder
Feeder by volume: 100m 0.5ml
Sample volume: 110ml-120ml
Funnel angle: 40 Degree, a pore size of 8mm

To meet K-6721 (1966) of the requirements

Apparent density analyzer

This method is suitable for measuring the apparent density of the powder molding compound, the mass per unit volume for molding plastic packaging, mold cavity and extrusion screw design provides parameters in line with GB / T 3402, GB 1636 standards.

Apparent density analyzer

1, Sample: extracting a sample standard product requirements.

2, the test instrument:

(1) balance: a sense of the amount of 0.1 g

(2) surface view tester

(3) The cylinder-type cup: 100 ml

3, Apparent density analyzer Test procedure:

(1) The funnel is placed on the instrument, the lower end of the small opening at the top of the measuring cylinder being 20-40 mm, and coaxial cylinder measurement possible.

(2) the striker plate into the funnel, the 100 + 5ml sample was poured into the funnel.

(3) blocking plate is pulled out quickly, the test flow freely into the measuring cylinder, the upper part of the measuring cylinder with a scraper to scrape off excess sample and on the balance of the sample cylinder weighed to the nearest 0.1 g.

(4) three times each batch tests (test sample has not re-use)

4, Apparent density analyzer test results

Mold material apparent density (D a , G / ml) is calculated as follows

m

Da=

v

Where: m- measure the quality of the cylinder in the sample (g)

v- volume measuring cylinder (100 ml)

The test results indicate the arithmetic mean of three measurements, taken two significant figures.

NOTE: There is also supporting the product, please contact us to maintain contact Zeng Sheng Phone: 15088416993

BT-300 powder tap densitometer


Tap density refers to an amount of powder packed in a container after a certain, to a certain frequency and amplitude of vibration, read out the volume of the volume of the powder when the powder is not reduced, and then divided by the volume of the powder by weight The tap density is obtained. BT-300 tap density tester Dandong Baxter Technology Co., Ltd. developed a special instrument to test a powder tap density, the instrument along with the 'dead weight' and 'fixed volume' Two test methods, therefore in line with China's national standard GB / T 21354-2008, equivalent in line with international standards ISO3953: 1993 and the tap density standard variety of industries, and in accordance with provisions of the United States Pharmacopeia Drug tap density, which is a Universal tap density instrument. BT-300 tap density tester by the timing system, control system, drive mechanism, actuators and ancillary spare parts and other components, having a vibration frequency is adjustable (to suit different industry measurement), easy to operate, durable, test accuracy and other characteristics, suitable for areas of non-metallic powder, metal powder, pharmaceuticals, chemicals, batteries, abrasives as well as research and teaching, is the ideal instrument powder industry tap density test.
The basic working process of BT-300 tap density tester is the rhythmic vibration powder cylinder fixed to the mechanical vibration device, vibration motor driven mechanical vibration device up and down vibration, graduated tube with powder containing mechanical vibration device occurs, with the increase the number of vibrations of the cylinder where the powder gradually tap, the number of vibrations after reaching the set number of times, mechanical vibration device to stop the vibration, volume readout graduated tube, according to the definition of density: mass divided by volume, thereby obtaining vibration After the powder density solid.

Basic indicators

  1. Repeatability: ≤1%
  2. Vibration amplitude: 3mm
  3. Vibration frequency: 250 times / min

Test items

  1. Fixed weight method to test tap density: first weigh a certain weight (usually 100 grams) of powder, all fitted to the cylinder, the cylinder containing the powder and then fixed to the instrument vibration, according to the powder surface of the rear end vibration The height of the visual volume and then calculate the tap density.
  2. Fixed-volume method to test the tap density (optional): First large amount of powder to 100ml tap density container loading (this container has extended tube), and secure it to the instrument vibration, vibration after the end of extended tube removed with a scraper 100 Calibrating the container mouth, and then weighed to calculate the weight of powder tap density.

DMP-II Type common abrasive bulk density tester

According to international standard ISO9136: 1989 (Determination of bulk density coarse grains) and industry standard JB / T7984.2-1999 (Ordinary coarse grit abrasive Determination of bulk density) of the relevant technical requirements of development and production of special detection equipment, suitable for detecting manufacturing bonded abrasives and coated abrasives bulk density of coarse particles of abrasive materials, but also for the detection of bulk density of other particulate materials and their detection methods and results and international common detection method has complete versatility.
1, the working principle
The abrasive test load funnel, open the drain valve, abrasive natural port along the funnel and into the measuring cylinder fall, and will fall into the measuring cylinder abrasive Calibrating the balance Weigh Calibrating the measuring cylinder abrasive quality, and then divided by the volume measuring cylinder, can be measured bulk density of abrasive measured.
2, the main technical parameters
2.1 Measurement error: ≤ ± 0.02g / cm3.
2.2 measuring cylinder volume: 200 ± 0.5cm3.
2.3 Dimensions: 230mm (length) * 250mm (width) * 425mm (H)