Hall flow meter, bulk density meter, flow tester

Hall flow meter, bulk density meter, flow tester
 

Product description:

Brand: RICO Ricoeur Model: FL4-1
  • Types of: other
Detailed description:
Repeatability error: 1 Samples can be measured state: Hall flow meter, bulk density meter, flow tester
Custom processing: Measuring range: Hall flow meter, bulk density meter, flow tester
Type: Density Tester Specifications:
Scope: Hall flow meter, bulk density meter, flow tester Dimensions: 1 (mm)

FT-102 Hall flow meter / Bulk Density Tester (stainless steel material)

FT-102 Hall flow meter flow and bulk density measuring device The instrument is replaced GB1479-84, GB1482-84 standard specification production with the design, production according to GB 1482-2010-T metal powder flowability measurement standard funnel (Hall flow meter). Its detection methods and results and international common detection method has versatility. This product is also applicable to similar powder powder flowability and bulk density measurements.

This device is intended for determination of metal powder flowability using a standard funnel in. Where can freely flow through the aperture to 2.5mm Standard funnel powder, can use this device.

Test Buju

1 Weigh 50g A sample, accurate to ± 0.1g .

2 Hand to block the hole at the bottom of the funnel, the weighed 50g Sample poured into the funnel, note the lower end of the powder must be filled funnel entire hole.

3 Moment when being opened holes and start timing funnel, powder funnel flow once completed, immediately stop the clock.

4 Record funnel all the time required to complete the sample stream, and repeated three times, and the arithmetic mean, the time recorded to the nearest 0.1s .

Note: If and when the hole being opened, the powder does not flow, you can tap on the funnel look to the powder begins to flow. However, even if this is done, the powder is still not out of or during the measurement of powder to stop the flow, you should consider this powder having no flowability.

Test Results

The arithmetic average of the three sample results are multiplied by the correction coefficient funnel to s / 50g reported data, report data is accurate to 0.5s.

Please fill in the test report: The test report shall include the following:

a. Necessary to explain the identification of the sample;

b. The handling of the sample, if the powder is dried, the drying process should be indicated;

c. If the flow of powder is caused due to the beat funnel should be specified;

d. Calculation results;

e. It may affect the outcome of any case.

FT-102 Hall flow meter / Bulk Density Tester It is based on national standards GB provisions of the design and production of 1482-84.

This device is intended for determination of metal powder flowability using a standard funnel in.

Where can freely flow through the aperture of 2.5mm standard funnel powder, can use this device.

FT-102 Hall flow meter / Bulk Density Tester Principle

Metal powder flowability to 50g metal powder to flow through a standard funnel predetermined aperture required to represent.

FT-102 Hall flow meter / Bulk Density Tester Technical Requirements

2.1 funnel (hole diameter 2.5mm)

Funnel made of stainless steel, and has a sufficient thickness and hardness to prevent deformation and excessive wear.

2.2 bracket, base and receiver

Bracket for fixing the funnel. Base for mounting bracket and receiver, adjust the level, stable and vibration free. Stand height adjustment and fixed with the supplied wrench, funnel attached to the bracket. Receiver (Stainless steel plate) is placed in the base on to collect powder.

2.3 Balances (user-supplied)

The largest weighing 100g; precision 0.05g.

2.4 Stopwatch

Measurement time can be accurate to 0.01s.

2.5 cups

The device is equipped with a volume of 25ml stainless steel measuring cup. Users can complete the determination of metal powder bulk density (Funnel method) reference to the provisions of the national standard GB 1479-84.

FT-102 Hall flow meter / Bulk Density Tester Basic configuration: The stand: 1 set; Funnel: Stainless steel (Φ2.5mm, Φ5.0mm) each one; cup; stainless steel (Φ31mm, 25ml) 1 只; stopwatch 1; overflow trays stainless steel 1; brush 1; ruler 15cm1 the manual; warranty card; certificate.

Ricoeur Instruments Companies' quality-oriented 'service first' operating principles. Meet the needs of our customers. Companies in the 'science and technology, creativity, innovation, progressive' entrepreneurial spirit, the introduction of advanced production equipment and manufacturing process, through continuous technology to improve and perfect the management, strive to provide customers the best quality products and service!

FT-102 Hall flow meter / Bulk Density Tester Operation video link:

http: //v.youku.com/ v_show / id_XMzc3NDYyODg0 html.

FL4-1 flowability and bulk density measuring instrument (brass)

FL4-1 flowability and bulk density measuring device (Brass) The instrument instead of GB1479-84, GB1482-84 Standard Specification for production according to GB 1482-2010-T metal powder flowability measurement standard funnel (Hall flow meter). The detection methods and results and international common The detection method has versatility. This product is also applicable to similar powder powder flowability and bulk density measurement

Standard funnel

5.1 Emery standard sample selection, particle size less than about 106 μ m When the method in accordance with the provisions of this standard be tested on a standard funnel liquidity of the standard sample should be 4 0 ± 0.5s / 50g.

5.2 Funnel been calibrated at the factory. When you start using the current user must be calibrated with a standard sample, measured correction factor standard samples should advance in air 10 At a temperature of 5 ± 10 ℃ drying 30min, then placed in a desiccator to cool to room temperature then measuring the flow of the sample Buju measuring standard sample, six times repeated measurements, in addition to the first, the other five measurements taken Arithmetic average. In general, the requirements for the maximum difference between the results of each measurement shall not exceed 0.4s. Ends assumed 50g standard sample from a standard funnel flow time is 40s, the correction coefficient of the funnel is 40.0 divided by 5 times the measurement results arithmetic mean.

5.3 Funnel in the course of a standard sample should be regularly proofread flow time if a standard sample in the funnel vary with time should be measured to calculate the average new new correction factor.

Note: 1, In the new proposal is adopted before the correction coefficient, the reason to study change. If the time is shortened, described by repeated use of the funnel, holes due to wear powder becomes large, and prove new correction number is correct. On the contrary, Director of the flow of time, indicating a soft powder attached to the wall of the hole should be carefully remove these deposits, then repeat the test.

2, When the funnel period of time, with the 50g standard sample measured flow time reduced to 37s or less, the funnel should be scrapped and replaced with a new funnel.

Ricoeur Instruments Also produces the following related products: Powder flowability tester / Bulk Density Tester / Hall flow meter / tap density tester / Scott capacity meter bulk density tester / bulk density Tester / aluminum powder Bulk Density Tester / measuring angle of repose instrument / angle of repose tester / apparent density analyzer / / aluminum fluoride (Alumina) Mobility analyzer, etc.













FL4-1 flowability and bulk density measuring device For measuring powder flowability and bulk density.

Under funnel diameter: φ2.5㎜ and φ5.0㎜

Angle: 60 degrees
Capacity: 25 ml

basic configuration: The stand: 1 set; funnel: (Φ2.5mm, Φ5.0mm) each one; cup; (Φ31mm, 25ml) 1 只; stopwatch 1; overflow trays 1; brush 1; ruler 15cm1 the manual ; warranty card; certificate.

FL4-1 flowability and bulk density measuring device (brass) Operation video link:

http: //v.youku.com/ v_show / id_XMzc1MTQxMjUy.html

Ricoeur instrument tips: You may be interested in the following products:

Common powder powder tester series

FT-100 tap density tester; FT-101 Scott capacity meter Bulk Density Tester
FT-102 Hall flow meter / Bulk Density Tester - stainless steel; FL4-1 Hall flow meter / powder flowability tester - brass FT-103 bulk density tester; FT-103A activated clay bulk density determination equipment;

FT-103B dust repose angle measurement; FT-104 alumina bulk density tester;

FT-104A repose angle measurement; FT-104B repose angle measurement; FT-104C aluminum fluoride mobility analyzer; apparent active agents tester FT-105A FT-105 Apparent density density measuring device; FT-105B slurry was apparent density measuring device; FT-105C ASTM plastic apparent densitometer; FT-106 abrasive bulk density tester (Original DMP-II)
FT-106A powder bulk density tester; FT-106B superhard material bulk density tester
FZS4-4 tap density tester; FT-102A vibration funnel bulk density tester

FZ4-3 bulk density of the funnel-type vibration analyzer; FS4-2 Skoda Bengtsson bulk density tester

DMP-II ordinary abrasive bulk density tester; FT-107 fertilizer bulk density (Loose) Tester