Supply FT-103B dust repose angle measurement, angle of repose tester

Supply FT-103B dust repose angle measurement, angle of repose tester
 

Product description:

Brand: Ricoeur Instrument Model: FT-103B
  • Types of: Density Tester
Detailed description:

FT-103B Dust analyzer angle of repose , Repose angle meter (injection limited underside of law)

FT-103B Dust analyzer angle of repose standard request

GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

FT-103B Dust analyzer angle of repose principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

FT-103B Dust analyzer angle of repose Test requirements and procedures

Angle of repose measuring device dust injection limited underside of law, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating poured into the funnel back out of the stopper. , so that dust from the funnel orifice outflow; for bad fluidity dust, dust can be used to make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays dust cone bus and the horizontal plane. clip acute angle, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

FT-103B Dust analyzer angle of repose Technical Parameters:

1, the funnel taper 60 ° ± 0.5 °;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;

Ricoeur instrument prompts you: You may also use the following package of products : FT-103B dust repose angle measurement; FT-103 bulk density meter repose; FT-104B repose angle measurement

FT-103B Dust analyzer angle of repose user's Guide
First, the scope
The products for production, management, and use of laboratory determination of physical properties of dust use.
This instrument is suitable for testing the angle of repose of dust.
Second, the applicable standard requirements:

Determination of GB / T16913-2008 dust angle of repose for the performance of

Third, the technical requirements

First, the standard requirements: GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

Third, the test requirements and procedures: the angle of repose of dust injection means defining a bottom surface measuring method, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating after Pour stopper out of the funnel, so that dust from the funnel orifice outflow; for bad fluidity dust, dust can make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays. dust cone bus sandwiched acute angle with the horizontal plane, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

Instructions
1, horizontal good analyzer.

2, will have a good pre-treatment sample using this meter standard 100ml cup installed.

3, the use of jamming bars, or other tools to block the leak funnel 6mm

4, to the sample, take away jamming bars or other tools

5, powder 80mm diameter vertical fall by material platform above, to form a taper.

6, using a protractor to measure the angle formed tapered concrete

Albert Instrument Co., Ltd. Ningbo Jiangbei Ricoeur

(Referred to as 'Ricoeur instrument' English: Ningbo Rlco instrument Co., LTD)

RICO Ricoeur began in 1999, the Department of Ricoeur instrument enterprise systems; Ricoeur instrument enterprise system is mainly engaged in analytical instruments, precision testing equipment and advanced detection equipment research and development, production, sales and after-sales service for the integration of the Industrial Company.

Which owns RICO Ricoeur 'trademark, the products meet the requirements of international standards of IEC, CCC, UL, CSA, VDE, JIS, KS, SEV, BSI, HD, KEMA, SSA and the like.

Companies' quality-oriented 'service first' operating principles. Meet the needs of our customers. Companies in the 'science and technology, creativity, innovation, progressive' entrepreneurial spirit, the introduction of advanced production equipment and manufacturing process, through continuous technology to improve and perfect the management, strive to provide customers the best quality products and service!

The company's business scope involving chemical, oil, polymer materials, powder metallurgy, powder powder, pharmaceuticals, batteries, plastics, construction materials, wire (Harness) processing, and other related industries.

Provide the most complete product testing solutions and technical advice for the production enterprises, research institutes and universities

FT-103B Dust analyzer angle of repose , Repose angle meter (injection limited underside of law)

FT-103B Dust analyzer angle of repose standard request

GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

FT-103B Dust analyzer angle of repose principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

FT-103B Dust analyzer angle of repose Test requirements and procedures

Angle of repose measuring device dust injection limited underside of law, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating poured into the funnel back out of the stopper. , so that dust from the funnel orifice outflow; for bad fluidity dust, dust can be used to make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays dust cone bus and the horizontal plane. clip acute angle, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

FT-103B Dust analyzer angle of repose Technical Parameters:

1, the funnel taper 60 ° ± 0.5 °;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;

Ricoeur instrument prompts you: You may also use the following package of products : FT-103B dust repose angle measurement; FT-103 bulk density meter repose; FT-104B repose angle measurement





FT-103B Dust analyzer angle of repose user's Guide
First, the scope
The products for production, management, and use of laboratory determination of physical properties of dust use.
This instrument is suitable for testing the angle of repose of dust.
Second, the applicable standard requirements:

Determination of GB / T16913-2008 dust angle of repose for the performance of

Third, the technical requirements

First, the standard requirements: GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

Third, the test requirements and procedures: the angle of repose of dust injection means defining a bottom surface measuring method, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating after Pour stopper out of the funnel, so that dust from the funnel orifice outflow; for bad fluidity dust, dust can make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays. dust cone bus sandwiched acute angle with the horizontal plane, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

Instructions
1, horizontal good analyzer.

2, will have a good pre-treatment sample using this meter standard 100ml cup installed.

3, the use of jamming bars, or other tools to block the leak funnel 6mm

4, to the sample, take away jamming bars or other tools

5, powder 80mm diameter vertical fall by material platform above, to form a taper.

6, using a protractor to measure the angle formed tapered concrete

Albert Instrument Co., Ltd. Ningbo Jiangbei Ricoeur

(Referred to as 'Ricoeur instrument' English: Ningbo Rlco instrument Co., LTD)

RICO Ricoeur began in 1999, the Department of Ricoeur instrument enterprise systems; Ricoeur instrument enterprise system is mainly engaged in analytical instruments, precision testing equipment and advanced detection equipment research and development, production, sales and after-sales service for the integration of the Industrial Company.

Which owns RICO Ricoeur 'trademark, the products meet the requirements of international standards of IEC, CCC, UL, CSA, VDE, JIS, KS, SEV, BSI, HD, KEMA, SSA and the like.

Companies' quality-oriented 'service first' operating principles. Meet the needs of our customers. Companies in the 'science and technology, creativity, innovation, progressive' entrepreneurial spirit, the introduction of advanced production equipment and manufacturing process, through continuous technology to improve and perfect the management, strive to provide customers the best quality products and service!

The company's business scope involving chemical, oil, polymer materials, powder metallurgy, powder powder, pharmaceuticals, batteries, plastics, construction materials, wire (Harness) processing, and other related industries.

Provide the most complete product testing solutions and technical advice for the production enterprises, research institutes and universities