Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose, Tester

Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose, Tester
 

Product description:

Brand: Ricoeur Model: FT-103B
  • Types of: other
Detailed description:
Custom processing: Type: Density Tester
Measuring range: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose Samples can be measured state: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose
Repeatability error: 1 Dimensions: 1 (mm)
Scope: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose Custom processing:
Type: Density Tester Measuring range: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose
Samples can be measured state: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose Repeatability error: 1
Dimensions: 1 (mm) Scope: Ricoeur brand dust analyzer angle of repose, repose angle measurement, angle of repose

FT-103B dust analyzer angle of repose

FT-103B dust analyzer angle of repose standard request

GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

FT-103B dust analyzer angle of repose principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

FT-103B dust analyzer angle of repose Test requirements and procedures

Angle of repose measuring device dust injection limited underside of law, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating poured into the funnel back out of the stopper. , so that dust from the funnel orifice outflow; for bad fluidity dust, dust can be used to make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays dust cone bus and the horizontal plane. clip acute angle, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

FT-103B dust analyzer angle of repose Technical Parameters:

1, the funnel taper 60 ° ± 0.5 °;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;

Ricoeur Instrument Related Products Recommended: Hall flow meter / flowability and bulk density measuring device / Hall flow meter / bulk density meter / powder fluidity and appearance Density Tester / powder flowability and bulk density measuring device measuring bulk density / bulk density Tester / bulk density tester / activated clay bulk density tester / ordinary abrasive bulk density tester quotes / particle packing density analyzer / GB 25571 Bulk density analyzer / GB / T 16913 bulk density tester / angle of repose tester / powder bulk density tester / bulk density meter factory dust / powder bulk density tester / Scott capacity meter / bulk density tester / Scott capacity meter Bulk Density Tester / powder Density Tester / vibration tap density tester / apparent density analyzer / Special Chemical apparent density analyzer / Plastic Profile Factory apparent density analyzer















FT-103B dust analyzer angle of repose

FT-103B dust analyzer angle of repose standard request

GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

FT-103B dust analyzer angle of repose principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

FT-103B dust analyzer angle of repose Test requirements and procedures

Angle of repose measuring device dust injection limited underside of law, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating poured into the funnel back out of the stopper. , so that dust from the funnel orifice outflow; for bad fluidity dust, dust can be used to make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays dust cone bus and the horizontal plane. clip acute angle, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

FT-103B dust analyzer angle of repose Technical Parameters:

1, the funnel taper 60 ° ± 0.5 °;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;

Ricoeur Instrument Related Products Recommended: Hall flow meter / flowability and bulk density measuring device / Hall flow meter / bulk density meter / powder fluidity and appearance Density Tester / powder flowability and bulk density measuring device measuring bulk density / bulk density Tester / bulk density tester / activated clay bulk density tester / ordinary abrasive bulk density tester quotes / particle packing density analyzer / GB 25571 Bulk density analyzer / GB / T 16913 bulk density tester / angle of repose tester / powder bulk density tester / bulk density meter factory dust / powder bulk density tester / Scott capacity meter / bulk density tester / Scott capacity meter Bulk Density Tester / powder Density Tester / vibration tap density tester / apparent density analyzer / Special Chemical apparent density analyzer / Plastic Profile Factory apparent density analyzer