| Custom processing:|| Type: Density Tester|
| Measuring range: Zhejiang powder flowability tester production|| Samples can be measured state: Zhejiang powder flowability tester production|
| Repeatability error: 1|| Dimensions: 1 (mm) |
| Scope: Zhejiang powder flowability tester production|| Custom processing:|
| Type: Density Tester|| Measuring range: Zhejiang powder flowability tester production|
| Samples can be measured state: Zhejiang powder flowability tester production|| Repeatability error: 1|
| Dimensions: 1 (mm) || Scope: Zhejiang powder flowability tester production|
FL4-1 flowability and bulk density measuring instrument (brass)
FL4-1 flowability and bulk density measuring device (brass) The instrument instead of GB1479-84, GB1482-84 standard specification according to GB 1482-2010-T metal powder flowability measurement standard funnel (Hall flow meter) production.
FL4-1 flowability and bulk density measuring device For measuring powder flowability and bulk density.
Under funnel diameter: φ2.5㎜ and φ5.0㎜
Angle: 60 degrees
Capacity: 25 ml
basic configuration: The stand: 1 set; funnel: (Φ2.5mm, Φ5.0mm) each one; cup; (Φ31mm, 25ml) 1 只; stopwatch 1; overflow trays 1; brush 1; ruler 15cm1 the manual ; warranty card; certificate.
FL4-1 flowability and bulk density measuring device (brass)
FT-102 Hall flow meter / Bulk Density Tester stainless steel material)
FT-102 Hall flow meter flow and bulk density measuring device The instrument is based on place of GB1479-84 GB 1482-2010-T metal powder flowability measurement standard funnel (Hall flow meter), provides design standards GB1482-84 production, production. The device is suitable for use standard funnel determination of metal powder flowability. Where can freely flow through the aperture to 2.5mm Standard funnel powder, can use this device.
FT-102 Hall flow meter / Bulk Density Tester It is based on national standards GB provisions of the design and production of 1482-84.
This device is intended for determination of metal powder flowability using a standard funnel in.
Where can freely flow through the aperture of 2.5mm standard funnel powder, can use this device.
FT-102 Hall flow meter / Bulk Density Tester Principle
Metal powder flowability to 50g metal powder to flow through a standard funnel predetermined aperture required to represent.
FT-102 Hall flow meter / Bulk Density Tester 2.1 funnel (hole diameter 2.5mm)
Funnel made of stainless steel, and has a sufficient thickness and hardness to prevent deformation and excessive wear.
2.2 bracket, base and receiver
Bracket for fixing the funnel. Base for mounting bracket and receiver, adjust the level, stable and vibration free. Stand height adjustment and fixed with the supplied wrench, funnel attached to the bracket. Receiver (Stainless steel plate) is placed in the base on to collect powder.
2.3 Balances (user-supplied)
The largest weighing 100g; precision 0.05g.
Measurement time can be accurate to 0.01s.
The device is equipped with a volume of 25ml stainless steel measuring cup. Users can complete the determination of metal powder bulk density (Funnel method) reference to the provisions of the national standard GB 1479-84.
FT-102 Hall flow meter / Bulk Density Tester Basic configuration: The stand: 1 set; Funnel: Stainless steel (Φ2.5mm, Φ5.0mm) each one; cup; stainless steel (Φ31mm, 25ml) 1 只; stopwatch 1; overflow trays stainless steel 1; brush 1; ruler 15cm1 the manual; warranty card; certificate.
FT-102 Hall flow meter / Bulk Density Tester
You may also be interested in the following products:
Common powder powder tester series
FT-100 tap density tester; FT-101 Scott capacity meter Bulk Density Tester
FT-102 Hall flow meter / Bulk Density Tester - stainless steel; FL4-1 Hall flow meter / powder flowability tester - brass FT-103 bulk density tester; FT-103A activated clay bulk density determination equipment;
FT-103B dust repose angle measurement; FT-104 alumina bulk density tester;
FT-104A repose angle measurement; FT-104B repose angle measurement; FT-104C aluminum fluoride mobility analyzer; apparent active agents tester FT-105A FT-105 Apparent density density measuring device; FT-105B slurry was apparent density measuring device; FT-105C ASTM plastic apparent densitometer; FT-106 abrasive bulk density tester (Original DMP-II)
FT-106A powder bulk density tester; FT-106B superhard material bulk density tester
FZS4-4 tap density tester; FT-102A vibration funnel bulk density tester
FZ4-3 bulk density of the funnel-type vibration analyzer; FS4-2 Skoda Bengtsson bulk density tester
DMP-II ordinary abrasive bulk density tester; FT-107 fertilizer bulk density (Loose) Tester
FT-102A vibration funnel Bulk Density Tester / Magnetic powder bulk density tester / vibration bulk densitometer / vibration funnel bulk density meter /
Vibratory Bulk Density Tester / Magnetic oxide powder densitometer / SJT 10215 Bulk Density Tester / ISO3923-3 metal powder bulk density meter
FT-102A vibration funnel bulk density tester: According to the standard : SJT 10215-1991 magnetic oxide powder bulk density measurement for determining the density of
. Fixed - Part 3 and measured according to ISO 3923/3 using metal powder bulk density of vibration funnel: Vibration funnel method
FT-102A vibration funnel bulk density tester: Scope This standard applies not freely flow through the aperture of 5mm magnetic oxide powder loose
Determination of bulk density of. Does not apply easily broken during vibration powder, such as needles and fibrous.
FT-102A vibration funnel bulk density tester: Instrument principle The powder was loaded into a hopper vibration device, under specified conditions of vibration, so pink
End from the hopper by a certain height free fall, filled with a known volume of a cylindrical cup. In the bulk state, the mass per unit volume of the powder in order to represent
Bulk density powder
FT-102A vibration funnel bulk density tester: Technical parameters
1, Funnel aperture of 7.5 mm, on the surface from the bottom of the hole and the cylindrical funnel cup is 25mm.
2, the vibrator power frequency 50Hz, funnel horizontally vibrations.
3, cylindrical cylinder capacity of 25 persons 0 5cm. Funnel taper 60 °
4, the funnel and cylindrical cup made of brass, and should have a certain wall thickness and hardness
5, Yao Ping should have enough weighing range, and precision weighing with disabilities can achieve 0.05 g. (User-supplied)
FT-102A vibration funnel bulk density tester