Supply Ricoeur instrument FT-104A | alumina, aluminum fluoride analyzer angle of repose angle of repose measuring device

Supply Ricoeur instrument FT-104A | alumina, aluminum fluoride analyzer angle of repose angle of repose measuring device
 

Product description:

Brand: Ricoeur Instrument Model: 104A
Detailed description:

The company Ricoeur instrument FT-104A alumina / aluminum fluoride Ann Murphy, quality assurance, welcome to consult the discussion.

FT-104A Alumina / Aluminum fluoride Angle of repose tester

(Alumina chemical analysis methods and determination of physical performance: Determination of repose angle) in accordance with national standards GB / T6609.24-2004 designed and manufactured for measuring the angle of repose of the powder under natural flow conditions.

1, in line YS / T581.13 alumina chemical analysis methods and determination of physical performance measured angle of repose) Technical Specification.
2, the product to meet the easy maintenance, safe, reliable, economical and practical aesthetic requirements.
3, equipment installation, commissioning and use
4, confirm the ready placement of the instrument bench is level.
5. The YS / T581.13 (alumina chemical analysis methods and determination of physical performance repose angle measurement) in the assembly diagram and technical specifications, for installation of the instrument.
Installation equipment .
1, the height of the fixed block placed on the lower discharge port, tighten the screws fixing the funnel. A guarantee 40mm height

2. Loosen the funnel bracket screw to adjust the center of the funnel with the floor to make it vertical.

3, according to the standard required to complete the test

FT-104A Alumina Angle of repose tester Meet GBT 16913-2008 dust and physical test methods GB / T 18702-2002 coal repose angle measuring method is also applicable to other products repose angle measurement, the measuring method is similar to the international phase.

Stainless steel funnel: The inner diameter of 74mm, 6mm inside diameter of the feed opening

Weight: about 16kg

Angle of repose of aluminum fluoride Measuring device

Angle of repose measuring device Mainly includes the following components:

1, stainless steel funnel: Neijing 74mm, inside through between the feed opening 6mm, two steps of aperture plate fitted with a sieve of 1mm This funnel is fastened to the bracket.

2, galvanized steel plate: material made of steel or marble, stainless steel and other corrosion-resistant base plate is made, the minimum size of: Width 200mm, length 270mm, 18mm thick plating on the polished floor of the four cross engraved on the surface 45. Angle straight. right in the center section of the funnel has a fixed height gauge positioning pin, the bottom plate below 3 adjustable horizontal feet.

3, Funnel Holder: composed of stainless steel, its structure should be perpendicular to the centerline of the fastening funnel centering pin.

4, height gauge (determine the height of the metal cylinder): It is a cylinder surface finish made of stainless steel, high 40mm, the bottom has a recess so that the center of the bottom plate with the locating pin convergence.

Ricoeur Instruments related products Recommended : FT-104A alumina / aluminum fluoride analyzer angle of repose; FT-104C aluminum fluoride (Alumina) Fluidity tester; FT-104 alumina bulk density tester

FT-104 alumina bulk density tester. Bulk density gauge aluminum fluoride

FT-104 alumina bulk density tester according to the standard

In line with GB (alumina chemical analysis methods and determination of physical performance bulk density determination) T 6609.25-2004 technical specifications. Determination of bulk density / alumina chemical analysis methods and determination of physical performance - Part 25.

FT-104 alumina bulk density tester technical parameters

1. Funnel: mouth diameter 100mm, taper 60º, within the discharge port by 6mm.

2. cylinder: about 200ml, the inner diameter of the inner high ratio of 1: 6, the base outer diameter of 70mm

3; Material: Stainless steel

Ricoeur instrument company related products Recommended: FT-104A alumina / aluminum fluoride analyzer angle of repose; FT-104C aluminum fluoride (Alumina) Fluidity tester; FT-104 alumina bulk density tester

FT-104 alumina bulk density tester requirements

Bulk density measuring device, including the following sections:

1, Funnel: upper inlet diameter 100mm, taper 60 °, neck length 8mm, brought in under the spout inside by 6mm.

2, cylindrical containers: volume of about 200mL, Nei Jing and about 1 in the high ratio: 6, the inner bottom is flat.

3, the annular funnel rack: There are pillars in the bottom stage of sturdy funnel annular mounting frame, long screws fixed to the pillars of the ring frame, and can be freely adjusted.

The funnel installed in the cylindrical container above the predetermined level surface.

This warranty card guarantee one year, to ensure that period, as a result of poor quality, or fault of manufacture, may favor free repair.

(A) load sensors, displacement, electromagnetic switches, I am afraid can not be around within the warranty period.

(B) the cost of material costs to close the case when the following circumstances.

① improper use or damage caused by a machine malfunction.

② damage caused by his failure is assembled to form the label.

③ beyond our waiter repair, resulting in failure when disassembly.

(3) when the following conditions without guarantee.

① accident due to natural disasters or other force majeure, which led to the failure or damage.

② the use of incorrect or alteration, damage caused by the machine.

Move or transport failure occurred after ③ installation.

(D) If the guarantee is lost, the product warranty period from the date of manufacture to guarantee one year.