[Measuring Instrument] - [Weighing & Measuring Apparatus] - [Other Weighing & Measuring Apparatus]

Supply DMP-II Type common abrasive bulk density meter, bulk density, abrasive accumulation tester

Supply DMP-II Type common abrasive bulk density meter, bulk density, abrasive accumulation tester
  • Supply DMP-II Type common abrasive bulk density meter, bulk density, abrasive accumulation tester
Product code: 20935300001
Unit price: 1 CNY  (0.15 USD)
Price unit: Per piece
Minimum order:
Other info:
Visit my shop
Brand: Ricoeur Instrument Model: FT-106
  • Types of: other
Detailed description:

The company DMP-II Type common abrasive bulk density tester, forging, quality assurance, welcome to consult the discussion.

106A Powder bulk density tester main pieces Instrument by the splice parts, vibration feed section, electrical control components.

FT-106A Powder bulk density tester Scope : Suitable for detecting manufacturing bonded abrasives and coated abrasives with powder bulk density, but also for the detection of diamond powder and bulk density of other fine powdery material, its detection methods and results and international common detection method has complete versatility.

FT-106A Powder bulk density tester main technical parameters

Funnel Material: Stainless Steel;

Funnel Dimensions: Height 290mm; catchy diameter 190mm; spout inner diameter: 28mm; spout height: 38mm

Vibration slot Material: Stainless Steel

Vibration tank size: (210mm * 40mm * 30mm) ± 1mm

Measuring cylinder dimensions: diameter 64mm; inner height 62.2mm

Measuring cylinder V: (200 ± 0.5) cm3

Measurement error: ≤ ± 0.02g / cm3

Under funnel mouth diameter: 28mm; cylinder volume: 200ml; funnel spout height: 38mm; height of the drop measured powder: 140mm.

Ricoeur instrument company offers related products : FT-106A powder bulk density tester; FT-106 ordinary abrasive bulk density tester;

FT-106B superhard material bulk density tester

Measurement methods

5.1 Preparation of test specimens

5.1.1. The test sample placed in an oven at 110 0 C and dried at a temperature of 1 hour, cooled to room temperature before measurement.

5.1.2. The test sample divided into thirds, removing one of which measuring bulk density, and the other two aside.

5.2 Measurement procedures

5.2.1 The best at room temperature (23 ± 2) 0 C; relative humidity is detected at (50 ± 6)% of the environment.

5.2.2. The test sample into the instrument of the funnel, the test specimen under its own stacking interactions in a stable state.

5.2.3. Press the electrical control part of the power switch, power indicator light. Then press electrical control vibration switch, then vibration indicator light, electromagnetic oscillator to work. Powder under the action of electromagnetic vibrations to specific ways and means of measuring flows into the bucket. inflow powder should be smooth, continuous process and there are rules.

5.2.4. When measuring soot accumulation in the center of the barrel, and a barrel higher than the measured upper edge 2cm ~ 3cm When pressed again electrical control vibration switch, the electromagnetic oscillator is stopped. Press again to electrical control power switch, turn off the power.

5.2.5. Remove the shield, should be careful not to remove the rest of the collision.

5.2.6. Will accumulate in the measuring bucket on top of the powder scraped with a straight blade, scraping the barrel when the angle between the blade and the measuring surface about 450 This process should prevent the compaction of powder measuring cylinder to avoid vibrations.

5.2.7. Indexing is not greater than 0.01g Weighing scales measuring quality powder keg and barrel, and then subtracting the measured quality of the barrel, the barrel fine powder derived measurement quality.

5.2.8. Measurement process, powder flows into the measurement time should be controlled in the tub 30 Sec to 90 Between seconds powder inflow time by the amplitude of the electrical part of the adjustment knob to adjust the controls, adjust the funnel to the bottom surface of the guide groove distance between the vibration can also affect the inflow velocity Powder.

5.2.9. Throughout the measuring process, we should always avoid vibration measurements barrel.

5.3. data processing

Bulk density is calculated as follows:

PB = M1 / V

Where: P B - Powder bulk density, unit: g / cm3;

M1 - Quality measuring cylinder powder, unit: g;

V - the volume of the measuring cylinder, unit: cm3.

5.4. Follow the steps 5.2.1 - 5.3 Bulk density measurements other duplicate samples.