Guangzhou, Sichuan repose angle measurement, angle of repose tester, angle of repose, Shaanxi and Shaanxi meter factory

Guangzhou, Sichuan repose angle measurement, angle of repose tester, angle of repose, Shaanxi and Shaanxi meter factory
 

Product description:

Brand: Ricoeur Model: FT-104A
  • Types of: other
Detailed description:
Repeatability error: Sichuan repose angle measurement Guangzhou Samples can be measured state: Sichuan repose angle measurement Guangzhou
Custom processing: Measuring range: Sichuan repose angle measurement Guangzhou
Type: angle of repose tester Specifications: Sichuan repose angle measurement Guangzhou
Scope: Sichuan repose angle measurement Guangzhou Dimensions: 1 (mm)

FT-104A repose angle measurement

(Alumina chemical analysis methods and determination of physical performance: Determination of repose angle) in accordance with national standards GB / T6609.24-2004 designed and manufactured for measuring the angle of repose of the powder under natural flow conditions meet GBT 16913-2008 dust physics. Test methods and GB / T 18702-2002 coal repose angle measuring method is also applicable to other products repose angle measurement, the measuring method is similar to the international phase.

Stainless steel funnel: The inner diameter of 74mm, 6mm inside diameter of the feed opening

Weight: about 16kg

FT-103B dust analyzer angle of repose

First, the standard requirements: GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

Second, the principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

Third, the test requirements and procedures: the angle of repose of dust injection means defining a bottom surface measuring method, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating after Pour stopper out of the funnel, so that dust from the funnel orifice outflow; for bad fluidity dust, dust can make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays. dust cone bus sandwiched acute angle with the horizontal plane, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

Fourth, the technical parameters:

1 Funnel taper 60 °±0.5°;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;











FT-104A repose angle measurement

(Alumina chemical analysis methods and determination of physical performance: Determination of repose angle) in accordance with national standards GB / T6609.24-2004 designed and manufactured for measuring the angle of repose of the powder under natural flow conditions meet GBT 16913-2008 dust physics. Test methods and GB / T 18702-2002 coal repose angle measuring method is also applicable to other products repose angle measurement, the measuring method is similar to the international phase.

Stainless steel funnel: The inner diameter of 74mm, 6mm inside diameter of the feed opening

Weight: about 16kg

FT-103B dust analyzer angle of repose

First, the standard requirements: GBT 16913-2008 dust dust physical test methods repose angle measurement (injection limited underside of law)

Second, the principle:

Sufficient overflowing trays dust injected from the mouth of the funnel to the horizontal feed tray; measure dust accumulation and the bottom horizontal bevel sandwiched acute angle, that dust angle of repose.

Third, the test requirements and procedures: the angle of repose of dust injection means defining a bottom surface measuring method, should be placed on the test stand; funnel plugged with a stopper spout would like dust sample loading cylinder filled with a blade Calibrating after Pour stopper out of the funnel, so that dust from the funnel orifice outflow; for bad fluidity dust, dust can make knitting stir continuously living on trays until all the dust out of the rotation protractor to measure out on trays. dust cone bus sandwiched acute angle with the horizontal plane, that angle of repose, and the records shall be continuously measured 3 times to 5 times, find the arithmetic mean and standard deviation a A

Fourth, the technical parameters:

1 Funnel taper 60 °±0.5°;

2, the outflow diameter 5mm, funnel and the lower center tray center should be on a vertical line;

3, along with the disk bottom spout distance 80mm 2 mm, protractor 7.5cm ~ 10 cm;

4, material disc diameter 80 mm, volume 100 ml graduated cylinder;

5, straight blade-like dust, knitting;