[Tools & Equipment] - [Drilling Tools] - [Drill Bit]

Hughes PDC cutter 1308 1313, 1613 1913 1616 1916

Hughes PDC cutter 1308 1313, 1613 1913 1616 1916
  • Hughes PDC cutter 1308 1313, 1613 1913 1616 1916
Product code: 20557300001
Unit price: 600 CNY  (87.21 USD)
Price unit:
Minimum order:
Other info: Black
Visit my shop

Because the shearing action of PDC cutters are more efficient than the crushing action of a button or tooth bit, fixed cutters are in high demand.

In 1982, PDC drill bits accounted for only 2% of total footage drilled. In 2010, 65% of total footage drilled was by PDCs.

Skip to: Common sizes of PDC cutters.

Related page: Directional Drilling
Related page: IADC Classification of Fixed Cutter Bits
Related page: Dull Grading a Fixed Cutter Bit


The diamond drill bit is used in nearly all applications including geothermal energy drilling, mining, water well and natural gas drilling and oil well drilling. Total depths range from 100 to 20000'.

PDC drill bits are used extensively in theBarnett Shale for natural gas drilling.


Impact damage, heat damage and abrasive wear all inhibit a drill bit's performance and can occur in even the softest geological formations. However, the most difficult formation for a PDC bit to drill are extremely abrasive ones.

With PDC popularity on the rise, bit manufacturing companies are seeking new materials and design aspects to make a tougher bit without compromising ROP.


PDC cutters are made using a combination of high heat and high pressure. Man made diamonds can be grown in 5-10 minutes. Because of this diamond content, a fixed cutter bit may also be known as a diamond drill bit.

High heat
plus pressure creates a
diamond compact.
Cutters are made from a carbide substrate and diamond grit.High heatof around 2800 degrees andhigh pressureof approximately 1000000 psi forms the compact. A cobalt alloy is also present and acts as a catalyst to the sintering process. The cobalt helps bond the carbide and diamond.

During the cooling process, the tungsten carbide shrinks at a rate of 2.5 times faster than the diamond. Controlling this stress, as with most aspects of PDC cutter design, is called Intellectual Property, and manufacturers rarely, if ever, share their secrets.


Small cutters
produce smaller

Large cutters produce
larger cuttings.
As a general rule, large cutters (19mm to 25mm) are more aggressive than small cutters. However, they may increase torque fluctuations. Additionally, if theBHAhas not been designed to handle the increased aggressiveness, instability may result.

Smaller cutters (8mm, 10mm, 13mm and 16mm) have been shown to drill at higher ROP than large cutters in certain applications. One such application is limestone.

Also, bit design employing smaller cutters have a higher cutter density; thus, enabling them to withstand higher impact loading.

Additionally, small cutters produce smaller cuttings while large cutters produce larger cuttings. Large cuttings may cause problems with hole cleaning if the drilling fluid cannot carry the cuttings up the annulus.


Mining/ Geothermal/ Shallow Oil and Gas

Cutter SizeDiameterHeight

08048.20 mm4.50 mm
08088.20 mm8.00 mm
100410.00 mm4.50 mm
130413.30 mm4.50 mm
130313.30 mm3.53 mm
130813.44 mm8.00 mm

Oilfield Drilling Bits

Cutter SizeDiameterHeight

130813.44 mm8.00 mm
131313.44 mm13.20 mm
1608.16.00 mm8.00 mm
161316.00 mm13.20 mm
190819.05 mm8.00 mm
191319.05 mm13.20 mm
191619.05 mm16.00 mm