4E1 to Ethernet Converter

4E1 to Ethernet Converter

Product description:

Product function: 4E1 to 10/100BT ethernet converter used back multiplexing technology, transfer 10M/ 100M Ethernet data by using multi E1 channels. Realize convert between 1 to 4 E1 channels and Ethernet interface. It can transmit signal of E1 channel to RJ45 interface point to point, realize the connection of E1 channel and Ethernet. It different from normal bridge , supporting 1 to 4 E1 channels customized configuration, auto detecting the number of E1 channels and use the available E1, allow some limiting transfer delay between different E1 channels. Single line speed is 1968Kbits/ s, 4 channels can up to 7872Kbits/ s. it can connect with Ethernet switch or hub when in 10/100Mbps full/ half duplex mode, make use of mass E1 resource in telecommunication networks to expend the transfer distance and application field of Ethernet, is a suitable solution for broadband switch in of Ethernet. It can used in fields such as connecting LANs, connecting end offices, VOD, remote monitor, E1 interface of switches, etc.

  • Realize transparent transfer Ethernet data in 1 to 4 E1 channels
  • 10M/ 100M Ethernet, full/ half duplex self adapt and 4 port Ethernet can save as a switch;
  • Ethernet support AUTO-MDIX ( cross over and straight through self adapt)
  • setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
  • Allow 4 E1 channels up to 10ms transfer delay. when the delay over the limitation, can stop transfer automatically.
  • Having 2 loop back functions: E1 local loop, E1 external loop.
  • Support Dynamic Ethernet MAC address (4096) , having local address filter function.
  • E1 interface compatible with ITU-T G. 703, G. 704, and G. 823. signaling slot not supported.
  • E1 interface having internal clock resume circuit and HDB3 codec circuit.
  • support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
  • supporting 1 to 4 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset.
  • E1 Support 75ohm/ unbalance impedance or 120ohm/ balance for option
  • support reset remote system from local system.
  • having Ethernet monitor auto reset function

    Parameter and specifications
    E1 interface
    Standard: E1 interface compatible with G. 703 standard.
    Rate: 2.048Mbit/ są50ppm
    Coding: HDB3
    Impedance: 75ohm (unbalance) or 120ohm (balance)
    Connector: BNC (75ohm) or RJ45 (120ohm)
    Jitter Performance: According to G. 742 and G. 823
    Rate: 10M/ 100M, full/ half duplex self adapt.
    Protocol: support IEEE 802.3, IEEE 802.1 P, 802.1Q (VLAN)
    MAC address table: 4096 MAC addresses.
    Ethernet buffer: 64Mbits SDRAM
    Physical interface: RJ45, support AUTO-MDIX (cross over and straight through self adapt)
    19inch Type: 433 mm (L) ¡Á138mm (W) ¡Á 44 mm (H)
    Operating environment
    Voltage: DC-48V , input range: DC-36V~DC-72V
    Power Consumption: (=5 Watts
    Working temperature: 0C~50C
    Storage temperature: -40C~+70C
    Humidity: 95%
    No causticity and solvent, dust free, and no strong magnetic interference.

    Related Link:
    What is the difference between TDM over IP and E1 to Ethernet converter ?