GPS Tracker, GPS positioning, GPS tracking, automotive ITES

GPS Tracker, GPS positioning, GPS tracking, automotive ITES
 

Product description:

GPS / GSM / GPRS vehicle positioning terminal

Model: TY-T18

Basic functions:

• tracking

• SMS inquiry Coordinates

• Emergency trigger alarm

• Remote power off the oil, compatible with the original vehicle anti-theft device

• Remote monitoring

• ACC detection

• electronic fence, mileage statistics

• Motion alarm

• speed alarm

• cross-border police

Services:

• Special anti-theft system Car rental companies, outdoor mechanical equipment

• Financial Insurance positioning tracking system

• Intelligent Vehicle bank credit management and monitoring systems

Command and Control System Management • Various industries vehicle

• Large or medium-sized construction vehicle devices

• Logistics Cargo Tracking

• private car anti-theft tracking

1 Introduction

This product is based on GSM / GPRS network and GPS satellite positioning system, short messaging, or remote target by mutual contact locate or monitor with a mileage statistics, ACC detection, power failure alarm function, compatible with the original vehicle anti-theft devices: car alarm After the alarm equipment is also alarm, notify the owner via SMS.

2 Applications

l car rental / small fleet management.

l global satellite positioning; vehicle location query; real-time monitoring; timing tracking

l remote control off the oil off track crime

l command vehicles in various industries, scheduling system.

3 Hardware Description

specification

content

specification

size

85mm x 63mm x 18mm (3.3 '* 2.5' * 0.71 ')

net weight

160g

The internet

GSM / GPRS / GPS

Network band

900/1800 / 1900Mhz (850 Mhz Optional)

chip

SIRF3 chip

GPS Module

Simcom900

GPS Sensitivity

-159dBm

GPS positioning accuracy

3-30 Meter

Data transmission

SMS, GPRS (CMNET)

Location query

Phone or platform

Operating Voltage

DC9V-30V

spare battery

3.7V 110mAh

Standby Current

(50mA

Storage temperature

-40 ° C to + 85 ° C

Operating temperature

-20 ° C to + 70 ° C

Operating relative humidity

5% -95% RH

Equipment start

5.3.1 The device connected to the car, and then the SIM Card into the device until the red light is on. The first time you use a satellite signal to outdoor areas.

5.3.2 in 10 To 40 Seconds, the device will search to GSM and GPS Signal and begins normal operation, the state of the device under normal blue lights every 2 Blinks once (blue light stays lit, GPS Module at work; but not locate; blue light has been lit; indicates GPS Module work, and has been positioned to . Fast flashing red lights indicate that the terminal device is communicating.)

5.3.3 When the device receives GPS After the signal is normal, you can use it and an instruction in any setting.

5.4 administrator number

5.4.1 Set the administrator number: Send SMS administrator + password' To the device in number, reply to set the administrator successful example: Instruction: Administrator 123456 (Initial password: 123456)

5.4.2 Remove the administrator number: Send SMS command to delete the number + Password + space + administrator number ' To the device in number, reply to the administrator to be deleted, for example: Administrator number is 13813813800, instruction: delete the number 123456 13813813800' (The default password is: 123456), after you remove the administrator number, device status changes from the administrator no administrator.

Note: The device has two operating modes, one is administrator mode, the other is non-Administrator mode device to factory settings without administrator mode in administrator mode there.. Only authorized number can only be set to operate the equipment (Authorized numbers refer to the use of the manual 5.5 ). In the absence of administrator mode, all numbers are set up to operate on.

5.5 Authorization Number

5.5.1 Add an authorization number without administrator status: Using a mobile phone dial equipment in the number, this number is recorded after turning on the equipment down automatically added as an authorized number. (Can record up to four numbers, the first five numbers will overwrite the first one number.)

5.5.2 Add authorization number has administrator status: Send SMS commands with the administrator number 'Add number + password + space + number' to the device in the numbers, Reply to 'add numbers success' for example: To add 13813813801 as an authorized number, the instruction: Add number 123456 13813813801 (only administrators numbers can be operated)

5.5.3 Remove authorization number without administrator status: (See Handbook 5.5.1)

5.5.4 Remove authorization number has administrator status: SMS command sent by the administrator number Delete number + password + space + number to the device in the numbers, Reply to 'delete numbers success' for example: To delete 13813813801 authorization number, the instruction: Delete number 123456 13813813801 (only administrator numbers can Send SMS.)

Password Manager 5.6

5.5.1 change Password: Send SMS commands to modify password + old password + space + new password to the device in the numbers, Reply to 'change the password success' for example: 888888 is new password modify instruction: Change Password 123,456,888,888.

5.5.2 Restore the initial password: Send SMS to restore the initial password to the device in the number, reply 'password is 123456'.

Note: There are administrators in the state, only the administrator numbers can send SMS commands, in the absence of an administrator state, all numbers can send SMS commands.

5.7 Mobile Positioning

5.7.1 Mobile Get latitude and longitude: Send SMS to mobile positioning device in number, reply to the following:



NOTE: Whether the device is shaped costumes administrator or no administrator under state, any number can send this message instructions.

5.7.3 Gets the location of a mobile phone device: Send SMS to get the location of the device in the number, reply to the location of the device.

Note: To support this feature, depending on the platform.

5.8 Platform Targeting

5.8.1 Equipment in the number of binding platform: Send SMS device number + equipment in the number to the device in number, reply 'Device number is' example: the equipment inside 13813813803 binding platform, the command: device number 13813813803 Reply to 'device number is 13813813803'.

5.8.2 Setting the IP address and port: Send SMS instruction address + IP address + port + port number to the device in the numbers, Reply to 'set the IP address and port of success' for example:. IP addresses 119.147.23.100 port 2332 ,instruction: address 119.147.23.100 port 2332 .

Note: Set the platform number, with the binding platform, to be valid according to the specific platform.

5.8.3 Continuous positioning platform:

Set continuous positioning platform: Send SMS positioning interval number + * + * + to the device in the numbers, Reply to 'set up automatic positioning successful example: 30 seconds pass a platform; a total mass 60 times; the instruction: positioning interval 30 frequency 60 .

NOTE: Positioning interval must be greater than 30 Sec; To send unlimited; frequency is set to 0 .

Cancellation continuous positioning platform: Send SMS to cancel the positioning device in number, reply 'Cancel successful positioning.

Note: This feature can be realized through the platform, to support this feature, depending on the platform.

5.8.4 ACC status:

ACC Open state: Development Send SMS commands ACC Development interval + interval to send the device in number, reply 'set ACC to develop transmission interval success' for example: 30 seconds to transfer a data platform, the command: ACC Development interval to send 30'

ACC Off state: Hair ACC off sending SMS commands sent to the device interval interval + in number, reply 'set ACC OFF transmission interval success' for example: 60 seconds to transfer a data platform, the command: ACC Development interval to send 60'

5.9 Remote control oil and circuit

5.9.1 Passage control

Disconnect the oil: Send SMS off oil + password , Reply to 'off oil success', and disconnect the vehicle's passage.

Recovery passage: Send SMS password oil + , Reply to 'oil success', and recover the oil vehicle.

5.9.2 Circuit control

OFF circuit: Send SMS off + password , Reply to 'power success', and disconnect the vehicle's passage.

Recovery circuit: Send SMS powered + password , Reply to 'power success', and recovery of the vehicle passage.

NOTE: The remote control oil road and circuit, in a state administrator, only the authorized number can be set to send SMS commands, in the absence of an administrator state, all numbers can send SMS commands.

5.10 Remote monitoring

Dial equipment in the number you can listen .

Any listener: Send SMS to any listening devices in the numbers, Reply to 'set any monitor success', all the numbers are monitored. Device default to this mode.

Limit monitoring: Send SMS limit listening to the device in the numbers, Reply to 'set limits monitor success', authorization number can listen.

Close monitoring: Close listeners send SMS commands to the device in number, reply 'off monitor success', all the numbers are not listening.

5.11 electronic fence

And positioning platform bindings use.

5.12 motion alarm

5.12.1 Set motion alarm: Send SMS ' Motion alarm ' To the device in the numbers, Reply to 'set the motion alarm success'. When starting this function, when the vehicle movement will send a text message 'motion alarm + longitude + latitude + speed + time + date' to set this feature phones on, suggesting that the vehicle has been moved up. This function must have a valid GPS signal in time.

5.12.2 Cancel the motion alarm: Send SMS Cancel the motion alarm ' To the device in number, reply 'Cancel the motion alarm success'.

Note: There are administrators in the state, only the authorized number can be set to send SMS commands, in the absence of an administrator state, all numbers can send SMS commands.

5.13 speed alarm

5.13.1 Set motion alarm: Send SMS Speed ​​alarm + speed ' To the device in the numbers, Reply to 'set speed alarm success'. When starting this function, the speed of the vehicle velocity exceeds the set time, it will send a message 'speed alarm + longitude + latitude + speed + Time + Date' Set this function to the phone, suggesting that the vehicle has been speeding up. This function must have a valid GPS signal in time.

5.13.2 Cancel speed alarm: Send SMS Cancel speeding alarm ' To the device in number, reply 'Cancel speeding alarm success'.

Note: There are administrators in the state, only the authorized number can be set to send SMS commands, in the absence of an administrator state, all numbers can send SMS commands.

5.14 Power failure alarm

When the power supply is cut off, the device send SMS alarm: Power alarm + latitude + longitude + speed + Time + Date 'to the administrator number and authorization number.

5.15 emergency alarm

Press and hold tight SOS Push button 3 Second, device sends SMS alarm 'emergency alarm + longitude + latitude + speed + Time + Date' to the administrator number and authorization number

5.16 Mileage statistics

And positioning platform bindings use.

5.17 device reboot

Send SMS Reboot the system + Password ' To the device in number, reply 'system is rebooting' and restart the machine, return to the oil supply state.