Quantities solar panels aluminum batten, the full range specifications, availability, fast

Quantities solar panels aluminum batten, the full range specifications, availability, fast

Product description:

Material: Aluminum Number of floors: Other Origin: Guangdong
Grade: A + Open: Manual Brands: Conrad
Color: silver Specification: 6m / support

Foshan Conrad focused on PC sun panel lighting system utilities 24-hour hotline: 15815688688 Zhuyuan Zhi

Shunde, Foshan City into a giant specializing in the production of decorative materials wholesale solar panels aluminum batten / aluminum closing edge lighting system and solar panels professional construction and installation accessories (SLIONTEC 5931/5932 butyl waterproof tape, EPDM seal waterproof tape / PC H type connector / PC board greenhouse accessories, etc.) .PC dedicated lighting plate aluminum accessories (Aluminum batten / aluminum income side) is mainly used to install fastening PC board, high-quality solar panels installed accessories to make beautiful lighting sun roof cover, and can more effectively solve the leakage problem after the construction of the installation, and we can provide you with professional PC sheet up to more than 60 kinds of accessories, convenient different keel skeleton construction and installation, can meet all your needs, and have their own professional R & D personnel constantly improve and update products, so you can have more choices.

Aluminum is mainly used for fixed installation layering stitching seams between PC sheet, with self-drilling screws, butyl waterproof tape and EPDM seals leak can effectively play the effect of water, and beautiful, long service life, will not cause corrosion on the plate .

Material: 6063

Specifications: Width 25mm / 30mm / 32mm / 35mm / 36mm / 38mm / 40mm / 43mm / 45mm / 48mm / 50mm / 55mm / 60mm * Length 6m / support (special lengths can be customized to inquire)

Buy a high-quality PC sun panels, the installation method shall not be treated the same plate leaking cracks will appear, such as construction quality problems, it is recommended to buy high-quality solar panels of aluminum alloy layering and EPDM waterproof seal tape and other professional installation accessories, so as to make high-quality sun board works to quality assurance.

Installation of solar panels:

1. Before installation; according to the area; installation; pressure; snow load and other selected sheets of different thickness

Power Pressure formula: Q = KV 2 Q represents a dynamic pressure N / M 2 , K = 0.613, V represents the design wind speed m / s

Changes in wind velocity fluctuations represented by the pressure coefficient, and shape of the building's shape, height, lighting system related. The positive and negative air pressure to represent different wind direction.

Just drop snow on snow load: per cm height weight 0.8 ~ 1.9kg / m2

Wet snow: Every centimeter height weight 2.8kg / m2

Practical applications; in addition to considering wind loads and snow loads outside; also need to consider the safety factor; PC sunshine board is usually 600 ~ 1200N / M 2 The range is guaranteed.

When installing arch, bending direction into a giant solar panels must be parallel to the direction in skeleton, namely along the direction of Lenz ribs bent, if bent in the wrong direction, the sheet is easily damaged.

2. The cold-formed arch installation

Into a giant solar panels can not thermoformed and cold-formed curved direct fixed installation, solar panels must follow the direction of the curved ribs shocked and more than a certain bending radius, usually 175 times the thickness.

3. surface mounting method

Into a giant sun-safe working pressure of 600 ~ 1200N / m 2 Layout Therefore, before installation should be in accordance with local various factors to determine the choice of plate thickness and skeleton.

Plate Installation recommendations:

Must ensure that the skeleton formation and cleaning 1. Before installation;

2. The first check the size of the plate and cut the amount of expansion reserve eligibility; pay special attention to leave enough uniform expansion gap; calculated as follows:
Total expansion gap = expansion coefficient * maximum temperature difference before and after the local installation * sheet length
Linear thermal expansion coefficient of 7.0 * 10-5 mm / mm. K, that is, the temperature is increased by 1 degree, 1m * 1m of the plate along the length and width directions of the expansion of 7.0 * 10-5 mm (0.07mm)

3. The thermal expansion coefficient of the plate and the support frame are different and need to stay in margin to withstand wind pressure, snow load, etc., so embedded in the amount to be set aside adequate, and thermal expansion and contraction of space. Usually the sheet edge extends into the cage 25mm or more, and at least two ribs shocked when mounting area; Rezhanglengsu general gap of 3mm per meter;

4. identify UV plate surface side; and to the side out installation; never allow the inward side of the UV installation;

5. When installing the sheet; protective film on the cover sheet of the joint compound will affect the binding and plate; so before installing the protective membrane around the lift plate 5 ~ 10cm; do not let the profile clamp protective film; but it can not lift too much; so as to avoid damage to the plate surface operations;
Note: Some workers when operating in the protective film sandwiched in profile; then draw lifted with a sharp tool and then printed; but often scratch the plate surface and cause damage to the plate;

6. Under cold-formed solar panels installed, the bending radius of not less than 175 times the sheet thickness; solar panels can only stare blankly along the direction of the curved ribs;

7. The board shall be fixed directly self drilling screw; shall reaming; all drilling diameter should be larger than the bolt diameter; leaving expansion and contraction gap; therefore when the material plate openings; aperture should be larger than the screw diameter 50%; avoid locking screws in the curved portion; avoid cracking plate;

8. The self-tapping screw tightening when the force should be uniform to ensure genuine compaction profile sealing strip and sheet, but also to prevent excessive locking screw, resulting in deformation of solar panels.

9. All pores should be filled in neutral sealant, neutral sealant and adhesive coating the exposed parts to prevent the infiltration of detergent edge, to prevent delay onset of crack; when found defective installation, site of leakage may occur in may be sealant compensate. Selection to choose the cured sealant remains soft, low modulus, elongation greater than 50% neutral weathering silicone rubber, before sizing must make aluminum and sheet surfaces clean and dry , so that no oil, dust, water vapor, dew and other debris, sizing should be uniform, smooth surface layer, and can not be uniform cross-section dimensions intermittent phenomenon; pay special attention to the neutral sealant used must advance Compatibility test sheet to avoid chemical reaction with the plate;

10. The center hole of the sheet edge spacing should be greater than or equal 2.5cm;

11. When surface mounting plate is recommended along flute rib direction tilted slightly inclined slope of at least 5 ° (per meter length, head-end high 10cm), to facilitate drainage, if belonging to snowy regions require more inclined to prevent snow is too thick.

12. The whole process is strictly prohibited plate installation foot pedal surface, shall be used across the plate Moveable pedal operation;

13. PC board cut length must be greater than the width before bending;

14. Plate immediately after installation requirements torn off the protective film, as a result of construction of the special requirements of the protection board, also must first torn off protective film, and then re-cover;

15. After installing the plate should be a self-test, in particular, should seriously do spray test, check for leaks and, if leakage hazard should be eliminated, and then check the appearance quality;

PC sunshine board Installation Other Considerations:

A selection of sealing materials, are required to use a neutral. For careful consideration, advises clients to do compatibility tests before use. Improper sealing material will lead to PC sun panels, polycarbonate panels destruction.

Try to mark the plate 2. Stake crossed protective film, such as to be directly marked on the plate, it is recommended to use crayons, avoid the use of sharp tools.

3. When new buildings cement surface is dry; PC sunshine plates are not in direct contact with it; even after the cement surface should also be done at the contact surface of the mat material other PC board and cement surfaces spaced plates and cement surfaces; preventing plate by cement corrosive alkaline substances

6. The sheet cleaning with a soft cloth or sponge dipped in a neutral soap or detergent scrub PC sunshine board surface dust, dirt, and then rinse thoroughly with water, and finally with a soft cloth.

7. If the board grease, wet paint, rubber tracks, it is recommended to use a soft cloth dipped in absolute alcohol scrub.

8. PC sun panels embedded framework should be preceded by the embedded portion of the protective film off.